AC not turning on

A tripped breaker or stabiliser, flat remote batteries, or a fault in the indoor unit’s controls.

Usually starts atPower, remote or control board

Air conditioner · diagnosis note 04

Not turning on

A tripped breaker or stabiliser, flat remote batteries, or a fault in the indoor unit’s controls.

Safe things to check first

  • Check the breaker and the stabiliser are on.
  • Put new batteries in the remote.
  • Many ACs wait a few minutes before restarting. Give it five minutes.

What we’ll look at

Checks the supply, the remote signal and the indoor unit’s controls.

Book a repair for this

Burning smell, sparks, or water near the socket? Switch off at the wall and unplug. Please don’t open panels or touch wiring. Leave electrical work to a technician.

Why it happens

AC not turning on: the usual causes

Most likely first. The first few are often things you can check yourself; the rest need a technician.

  1. Tripped MCB or switched-off supply

    An AC is usually wired to its own heavy-duty socket or isolator switch, often with its own MCB. A surge, a storm or a fault on the circuit can trip it. If the indoor unit’s display is dark and it doesn’t beep, check the MCB and the wall switch before anything else. If the MCB trips again straight away, leave it off.

  2. Stabiliser cut-out or delay

    A stabiliser cuts the AC off when the voltage goes too high or too low, and most wait a few minutes after the power returns before switching on, to protect the compressor. Look at its indicator lights: a high, low or delay light means it’s doing its job, not that the AC has failed.

  3. Remote batteries or key lock

    If the AC doesn’t beep when you press On, the remote may not be sending a signal. Weak batteries can still light the remote’s display without powering its infrared signal. Many remotes also have a key lock that ignores the buttons until it’s switched off; your manual shows how.

  4. Restart delay after a power cut

    Many ACs wait about three minutes before restarting the compressor after being switched off or after a power cut, so the pressures in the system can settle. The indoor fan may run while the outdoor unit stays quiet. Some ACs don’t come back on by themselves at all unless auto-restart is enabled. Switching on and off repeatedly only restarts the wait.

  5. Timer, sleep or app schedule

    An off-timer, a sleep timer or a schedule set in the AC’s phone app can switch it off, or stop it coming on, when you expect it to run. Look for a timer or clock symbol on the remote’s display, and cancel any timer before deciding the AC is faulty.

  6. Control board, sensor or wiring fault

    If the supply is on, the stabiliser shows normal and the AC still doesn’t respond, or it shows a blinking light or an error code, the fault is likely in the indoor unit: the control board, its fuse, the display and receiver board, or the wiring between the units. That needs testing by a technician.

Stop and call

When to stop using it

  • The MCB trips again as soon as you switch the AC on.
  • You smell burning, or see scorch marks on the plug, socket or stabiliser.
  • The indoor unit blinks an error code that comes back after a restart.

Prevention

How to stop it happening again

  • Keep the AC on its own heavy-duty socket, never an extension board or a multi-plug.
  • Where the voltage swings often, use a stabiliser or surge protector rated for your AC.
  • Switch the AC off with the remote before switching off at the wall.
  • During long power cuts, switch off at the wall so the AC isn’t hit by a surge when power returns.

FAQs

AC not turning on: questions

Something else? Call +91 77604 72807

Why is my AC not turning on after a power cut?

Many ACs wait a few minutes before restarting after a power cut, and a stabiliser adds its own delay on top. Some stay off until you press On again. If nothing happens after five minutes, check the MCB: a surge when the power returns can trip it. If it trips again, leave it off and have it checked.

Why does my AC keep tripping the MCB?

One trip after a storm or surge may be a one-off. If it trips every time the AC starts, something is drawing too much current: a compressor or capacitor fault, damaged wiring or a short in one of the units. Don’t keep resetting it. Leave the AC off and have it tested.

Does an inverter AC need a stabiliser?

Many inverter ACs are built to run across a wide voltage range and don’t need a separate stabiliser; the spec label or manual gives the range. If the voltage in your area often goes outside it, or swings sharply, a stabiliser rated for the AC still protects it. When unsure, go by the manual.

How it works

From your call to a working appliance

Four steps, and you know the cost before anything is fixed.

  1. Select your appliance

    Pick it in the form, or just tell us on the phone.

  2. Tell us the problem

    What it’s doing, any error code, and the brand and model if you have them.

  3. Confirm inspection and estimate

    We agree a visit, inspect it at home, and give you the cost. Nothing starts until you say yes.

  4. Repair and testing

    We fix it, then test it with you before we leave.

Book a service

One home. Many appliances. One place to start.

Send the details and we’ll confirm a visit time by phone. Or just call.

Rather talk?+91 77604 72807 WhatsApp enquiry
Every day, 9 am – 9 pm
Bangalore, Karnataka

Service request

Takes about a minute. Nothing is stored.

Your details only go into the message you choose to send us. Nothing is stored on this website. Privacy